Voltage of sounds of MP3 files












6












$begingroup$


What is the maximum voltage for common music files?



When playing back on a smartphone, if the volume of the smartphone is set to maximum, how much voltage is sent to the earphones of the electric signal?










share|improve this question









New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.







$endgroup$








  • 9




    $begingroup$
    if you really think about what you asked, then you will realise that you asked the kind of question that is un-answerable .... you did not define the parameters of the music file contents ........ a similar un-answerable question is how loud is music?
    $endgroup$
    – jsotola
    23 hours ago






  • 1




    $begingroup$
    Perhaps this is a question about the electrical interface between an audio device and a headphone or earphone set rather than a question about sampled audio data.
    $endgroup$
    – Solomon Slow
    23 hours ago






  • 7




    $begingroup$
    The MP3 records sound intensity in a range between zero and maximum. The hardware playing the MP3 decides what "Maximum" means.
    $endgroup$
    – J...
    21 hours ago






  • 1




    $begingroup$
    It depends on the phone and the earphone impedance, but iPhone 6 produces a maximum of about 1V RMS according to this link: anandtech.com/show/8554/the-iphone-6-review/11
    $endgroup$
    – Ken Shirriff
    21 hours ago
















6












$begingroup$


What is the maximum voltage for common music files?



When playing back on a smartphone, if the volume of the smartphone is set to maximum, how much voltage is sent to the earphones of the electric signal?










share|improve this question









New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.







$endgroup$








  • 9




    $begingroup$
    if you really think about what you asked, then you will realise that you asked the kind of question that is un-answerable .... you did not define the parameters of the music file contents ........ a similar un-answerable question is how loud is music?
    $endgroup$
    – jsotola
    23 hours ago






  • 1




    $begingroup$
    Perhaps this is a question about the electrical interface between an audio device and a headphone or earphone set rather than a question about sampled audio data.
    $endgroup$
    – Solomon Slow
    23 hours ago






  • 7




    $begingroup$
    The MP3 records sound intensity in a range between zero and maximum. The hardware playing the MP3 decides what "Maximum" means.
    $endgroup$
    – J...
    21 hours ago






  • 1




    $begingroup$
    It depends on the phone and the earphone impedance, but iPhone 6 produces a maximum of about 1V RMS according to this link: anandtech.com/show/8554/the-iphone-6-review/11
    $endgroup$
    – Ken Shirriff
    21 hours ago














6












6








6





$begingroup$


What is the maximum voltage for common music files?



When playing back on a smartphone, if the volume of the smartphone is set to maximum, how much voltage is sent to the earphones of the electric signal?










share|improve this question









New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.







$endgroup$




What is the maximum voltage for common music files?



When playing back on a smartphone, if the volume of the smartphone is set to maximum, how much voltage is sent to the earphones of the electric signal?







voltage sound






share|improve this question









New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question









New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question








edited 5 hours ago









Peter Mortensen

1,60031422




1,60031422






New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked 23 hours ago









たくまいわきたくまいわき

374




374




New contributor




たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






たくまいわき is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.








  • 9




    $begingroup$
    if you really think about what you asked, then you will realise that you asked the kind of question that is un-answerable .... you did not define the parameters of the music file contents ........ a similar un-answerable question is how loud is music?
    $endgroup$
    – jsotola
    23 hours ago






  • 1




    $begingroup$
    Perhaps this is a question about the electrical interface between an audio device and a headphone or earphone set rather than a question about sampled audio data.
    $endgroup$
    – Solomon Slow
    23 hours ago






  • 7




    $begingroup$
    The MP3 records sound intensity in a range between zero and maximum. The hardware playing the MP3 decides what "Maximum" means.
    $endgroup$
    – J...
    21 hours ago






  • 1




    $begingroup$
    It depends on the phone and the earphone impedance, but iPhone 6 produces a maximum of about 1V RMS according to this link: anandtech.com/show/8554/the-iphone-6-review/11
    $endgroup$
    – Ken Shirriff
    21 hours ago














  • 9




    $begingroup$
    if you really think about what you asked, then you will realise that you asked the kind of question that is un-answerable .... you did not define the parameters of the music file contents ........ a similar un-answerable question is how loud is music?
    $endgroup$
    – jsotola
    23 hours ago






  • 1




    $begingroup$
    Perhaps this is a question about the electrical interface between an audio device and a headphone or earphone set rather than a question about sampled audio data.
    $endgroup$
    – Solomon Slow
    23 hours ago






  • 7




    $begingroup$
    The MP3 records sound intensity in a range between zero and maximum. The hardware playing the MP3 decides what "Maximum" means.
    $endgroup$
    – J...
    21 hours ago






  • 1




    $begingroup$
    It depends on the phone and the earphone impedance, but iPhone 6 produces a maximum of about 1V RMS according to this link: anandtech.com/show/8554/the-iphone-6-review/11
    $endgroup$
    – Ken Shirriff
    21 hours ago








9




9




$begingroup$
if you really think about what you asked, then you will realise that you asked the kind of question that is un-answerable .... you did not define the parameters of the music file contents ........ a similar un-answerable question is how loud is music?
$endgroup$
– jsotola
23 hours ago




$begingroup$
if you really think about what you asked, then you will realise that you asked the kind of question that is un-answerable .... you did not define the parameters of the music file contents ........ a similar un-answerable question is how loud is music?
$endgroup$
– jsotola
23 hours ago




1




1




$begingroup$
Perhaps this is a question about the electrical interface between an audio device and a headphone or earphone set rather than a question about sampled audio data.
$endgroup$
– Solomon Slow
23 hours ago




$begingroup$
Perhaps this is a question about the electrical interface between an audio device and a headphone or earphone set rather than a question about sampled audio data.
$endgroup$
– Solomon Slow
23 hours ago




7




7




$begingroup$
The MP3 records sound intensity in a range between zero and maximum. The hardware playing the MP3 decides what "Maximum" means.
$endgroup$
– J...
21 hours ago




$begingroup$
The MP3 records sound intensity in a range between zero and maximum. The hardware playing the MP3 decides what "Maximum" means.
$endgroup$
– J...
21 hours ago




1




1




$begingroup$
It depends on the phone and the earphone impedance, but iPhone 6 produces a maximum of about 1V RMS according to this link: anandtech.com/show/8554/the-iphone-6-review/11
$endgroup$
– Ken Shirriff
21 hours ago




$begingroup$
It depends on the phone and the earphone impedance, but iPhone 6 produces a maximum of about 1V RMS according to this link: anandtech.com/show/8554/the-iphone-6-review/11
$endgroup$
– Ken Shirriff
21 hours ago










3 Answers
3






active

oldest

votes


















15












$begingroup$

Amplification



It does not depend on the music file, but at the amplifier sending the music to a speaker, or to a headphone/earplug connector.



Music file



A music file only contains 'values', and mostly in a compressed form. After uncompressing, you get values which has a certain amount on bits per value (typically 16 or more).



Conversion



A microcontroller can send these values to a speaker via an pre- and/or amplifier, which converts it into actual voltages. So it depends on the amount of amplification.



Protection



Also note that sending continuous 'max values' do not result in a loud sound, actually it would breaks the speaker (to prevent this, in the amplifier a so-called DC speaker protection is present). A wave is needed to let the speaker move outwards and inwards very fast, and this is done by sending changing values to the speaker.



Measure



If you want to measure, you can use an oscilloscope to measure the audio output while sending a sine wave with a maximum amplitude.






share|improve this answer











$endgroup$









  • 9




    $begingroup$
    Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
    $endgroup$
    – Solomon Slow
    23 hours ago






  • 2




    $begingroup$
    @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
    $endgroup$
    – Michel Keijzers
    23 hours ago






  • 3




    $begingroup$
    @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
    $endgroup$
    – UKMonkey
    13 hours ago










  • $begingroup$
    @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
    $endgroup$
    – Mołot
    4 hours ago










  • $begingroup$
    @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
    $endgroup$
    – UKMonkey
    4 hours ago



















5












$begingroup$

These days a lot of DAC chips for consumer equipment use voltage output of 2 Vrms.



The supply voltage is largely irrelevant, as a lot of DAC chips also use internal charge pumps to boost up supply voltage and to generate negative supply voltage for the audio output stage, so they can drive DC coupled loads directly.






share|improve this answer











$endgroup$













  • $begingroup$
    "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
    $endgroup$
    – Sjoerd
    2 hours ago



















3












$begingroup$

Normally it's limited by the cellphone battery voltage, which is about 3.7V. However there are other limits in play like the EU volume limit of 100dB - which is specified as SPL rather than a voltage.






share|improve this answer









$endgroup$













    Your Answer





    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("mathjaxEditing", function () {
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
    });
    });
    }, "mathjax-editing");

    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("schematics", function () {
    StackExchange.schematics.init();
    });
    }, "cicuitlab");

    StackExchange.ready(function() {
    var channelOptions = {
    tags: "".split(" "),
    id: "135"
    };
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function() {
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled) {
    StackExchange.using("snippets", function() {
    createEditor();
    });
    }
    else {
    createEditor();
    }
    });

    function createEditor() {
    StackExchange.prepareEditor({
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader: {
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    },
    onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    });


    }
    });






    たくまいわき is a new contributor. Be nice, and check out our Code of Conduct.










    draft saved

    draft discarded


















    StackExchange.ready(
    function () {
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f429142%2fvoltage-of-sounds-of-mp3-files%23new-answer', 'question_page');
    }
    );

    Post as a guest















    Required, but never shown

























    3 Answers
    3






    active

    oldest

    votes








    3 Answers
    3






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    15












    $begingroup$

    Amplification



    It does not depend on the music file, but at the amplifier sending the music to a speaker, or to a headphone/earplug connector.



    Music file



    A music file only contains 'values', and mostly in a compressed form. After uncompressing, you get values which has a certain amount on bits per value (typically 16 or more).



    Conversion



    A microcontroller can send these values to a speaker via an pre- and/or amplifier, which converts it into actual voltages. So it depends on the amount of amplification.



    Protection



    Also note that sending continuous 'max values' do not result in a loud sound, actually it would breaks the speaker (to prevent this, in the amplifier a so-called DC speaker protection is present). A wave is needed to let the speaker move outwards and inwards very fast, and this is done by sending changing values to the speaker.



    Measure



    If you want to measure, you can use an oscilloscope to measure the audio output while sending a sine wave with a maximum amplitude.






    share|improve this answer











    $endgroup$









    • 9




      $begingroup$
      Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
      $endgroup$
      – Solomon Slow
      23 hours ago






    • 2




      $begingroup$
      @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
      $endgroup$
      – Michel Keijzers
      23 hours ago






    • 3




      $begingroup$
      @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
      $endgroup$
      – UKMonkey
      13 hours ago










    • $begingroup$
      @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
      $endgroup$
      – Mołot
      4 hours ago










    • $begingroup$
      @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
      $endgroup$
      – UKMonkey
      4 hours ago
















    15












    $begingroup$

    Amplification



    It does not depend on the music file, but at the amplifier sending the music to a speaker, or to a headphone/earplug connector.



    Music file



    A music file only contains 'values', and mostly in a compressed form. After uncompressing, you get values which has a certain amount on bits per value (typically 16 or more).



    Conversion



    A microcontroller can send these values to a speaker via an pre- and/or amplifier, which converts it into actual voltages. So it depends on the amount of amplification.



    Protection



    Also note that sending continuous 'max values' do not result in a loud sound, actually it would breaks the speaker (to prevent this, in the amplifier a so-called DC speaker protection is present). A wave is needed to let the speaker move outwards and inwards very fast, and this is done by sending changing values to the speaker.



    Measure



    If you want to measure, you can use an oscilloscope to measure the audio output while sending a sine wave with a maximum amplitude.






    share|improve this answer











    $endgroup$









    • 9




      $begingroup$
      Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
      $endgroup$
      – Solomon Slow
      23 hours ago






    • 2




      $begingroup$
      @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
      $endgroup$
      – Michel Keijzers
      23 hours ago






    • 3




      $begingroup$
      @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
      $endgroup$
      – UKMonkey
      13 hours ago










    • $begingroup$
      @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
      $endgroup$
      – Mołot
      4 hours ago










    • $begingroup$
      @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
      $endgroup$
      – UKMonkey
      4 hours ago














    15












    15








    15





    $begingroup$

    Amplification



    It does not depend on the music file, but at the amplifier sending the music to a speaker, or to a headphone/earplug connector.



    Music file



    A music file only contains 'values', and mostly in a compressed form. After uncompressing, you get values which has a certain amount on bits per value (typically 16 or more).



    Conversion



    A microcontroller can send these values to a speaker via an pre- and/or amplifier, which converts it into actual voltages. So it depends on the amount of amplification.



    Protection



    Also note that sending continuous 'max values' do not result in a loud sound, actually it would breaks the speaker (to prevent this, in the amplifier a so-called DC speaker protection is present). A wave is needed to let the speaker move outwards and inwards very fast, and this is done by sending changing values to the speaker.



    Measure



    If you want to measure, you can use an oscilloscope to measure the audio output while sending a sine wave with a maximum amplitude.






    share|improve this answer











    $endgroup$



    Amplification



    It does not depend on the music file, but at the amplifier sending the music to a speaker, or to a headphone/earplug connector.



    Music file



    A music file only contains 'values', and mostly in a compressed form. After uncompressing, you get values which has a certain amount on bits per value (typically 16 or more).



    Conversion



    A microcontroller can send these values to a speaker via an pre- and/or amplifier, which converts it into actual voltages. So it depends on the amount of amplification.



    Protection



    Also note that sending continuous 'max values' do not result in a loud sound, actually it would breaks the speaker (to prevent this, in the amplifier a so-called DC speaker protection is present). A wave is needed to let the speaker move outwards and inwards very fast, and this is done by sending changing values to the speaker.



    Measure



    If you want to measure, you can use an oscilloscope to measure the audio output while sending a sine wave with a maximum amplitude.







    share|improve this answer














    share|improve this answer



    share|improve this answer








    edited 1 hour ago

























    answered 23 hours ago









    Michel KeijzersMichel Keijzers

    6,73092970




    6,73092970








    • 9




      $begingroup$
      Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
      $endgroup$
      – Solomon Slow
      23 hours ago






    • 2




      $begingroup$
      @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
      $endgroup$
      – Michel Keijzers
      23 hours ago






    • 3




      $begingroup$
      @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
      $endgroup$
      – UKMonkey
      13 hours ago










    • $begingroup$
      @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
      $endgroup$
      – Mołot
      4 hours ago










    • $begingroup$
      @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
      $endgroup$
      – UKMonkey
      4 hours ago














    • 9




      $begingroup$
      Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
      $endgroup$
      – Solomon Slow
      23 hours ago






    • 2




      $begingroup$
      @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
      $endgroup$
      – Michel Keijzers
      23 hours ago






    • 3




      $begingroup$
      @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
      $endgroup$
      – UKMonkey
      13 hours ago










    • $begingroup$
      @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
      $endgroup$
      – Mołot
      4 hours ago










    • $begingroup$
      @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
      $endgroup$
      – UKMonkey
      4 hours ago








    9




    9




    $begingroup$
    Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
    $endgroup$
    – Solomon Slow
    23 hours ago




    $begingroup$
    Re, "...actually it breaks the speaker." If I can create a sound file that blows your speakers when you play it, the fault is not in my file. Your music player should at least be able to survive any sound file that you try to play.
    $endgroup$
    – Solomon Slow
    23 hours ago




    2




    2




    $begingroup$
    @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
    $endgroup$
    – Michel Keijzers
    23 hours ago




    $begingroup$
    @SolomonSlow Good point, I updated my answer (and learnt something myself from it).
    $endgroup$
    – Michel Keijzers
    23 hours ago




    3




    3




    $begingroup$
    @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
    $endgroup$
    – UKMonkey
    13 hours ago




    $begingroup$
    @SolomonSlow Some speakers won't be very happy if you play a mono-tone at a resonant frequency; And it happens quite often with sub woofer speakers; I'm sure you've heard some where the cone has been damaged. I agree the ideal is that the speaker should survive any input; but realistically if you find the right resonant frequency the damping of the speaker might not be sufficient to protect it.
    $endgroup$
    – UKMonkey
    13 hours ago












    $begingroup$
    @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
    $endgroup$
    – Mołot
    4 hours ago




    $begingroup$
    @UKMonkey I'd reword it to "music system should survive any sound that can be reasonably expected to happen during normal use". And I agree that many sub woofers are badly (or rather - cheaply) designed and do not.
    $endgroup$
    – Mołot
    4 hours ago












    $begingroup$
    @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
    $endgroup$
    – UKMonkey
    4 hours ago




    $begingroup$
    @Mołot no - I would say that a speaker shouldn't be damaged by the amplifier for any output of the amp within the acceptable ranges supported by the speaker. This means that if the speaker needs to be rated for a lower voltage (be it by shipping with a different amp or something else) to ensure it doesn't self destruct at 20Hz; then that's what it needs to do.
    $endgroup$
    – UKMonkey
    4 hours ago













    5












    $begingroup$

    These days a lot of DAC chips for consumer equipment use voltage output of 2 Vrms.



    The supply voltage is largely irrelevant, as a lot of DAC chips also use internal charge pumps to boost up supply voltage and to generate negative supply voltage for the audio output stage, so they can drive DC coupled loads directly.






    share|improve this answer











    $endgroup$













    • $begingroup$
      "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
      $endgroup$
      – Sjoerd
      2 hours ago
















    5












    $begingroup$

    These days a lot of DAC chips for consumer equipment use voltage output of 2 Vrms.



    The supply voltage is largely irrelevant, as a lot of DAC chips also use internal charge pumps to boost up supply voltage and to generate negative supply voltage for the audio output stage, so they can drive DC coupled loads directly.






    share|improve this answer











    $endgroup$













    • $begingroup$
      "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
      $endgroup$
      – Sjoerd
      2 hours ago














    5












    5








    5





    $begingroup$

    These days a lot of DAC chips for consumer equipment use voltage output of 2 Vrms.



    The supply voltage is largely irrelevant, as a lot of DAC chips also use internal charge pumps to boost up supply voltage and to generate negative supply voltage for the audio output stage, so they can drive DC coupled loads directly.






    share|improve this answer











    $endgroup$



    These days a lot of DAC chips for consumer equipment use voltage output of 2 Vrms.



    The supply voltage is largely irrelevant, as a lot of DAC chips also use internal charge pumps to boost up supply voltage and to generate negative supply voltage for the audio output stage, so they can drive DC coupled loads directly.







    share|improve this answer














    share|improve this answer



    share|improve this answer








    edited 4 hours ago

























    answered 18 hours ago









    JustmeJustme

    1,9821413




    1,9821413












    • $begingroup$
      "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
      $endgroup$
      – Sjoerd
      2 hours ago


















    • $begingroup$
      "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
      $endgroup$
      – Sjoerd
      2 hours ago
















    $begingroup$
    "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
    $endgroup$
    – Sjoerd
    2 hours ago




    $begingroup$
    "2 Vrms" here means 2 volts on average, where RMS (root mean square) is the method of calculating the average.
    $endgroup$
    – Sjoerd
    2 hours ago











    3












    $begingroup$

    Normally it's limited by the cellphone battery voltage, which is about 3.7V. However there are other limits in play like the EU volume limit of 100dB - which is specified as SPL rather than a voltage.






    share|improve this answer









    $endgroup$


















      3












      $begingroup$

      Normally it's limited by the cellphone battery voltage, which is about 3.7V. However there are other limits in play like the EU volume limit of 100dB - which is specified as SPL rather than a voltage.






      share|improve this answer









      $endgroup$
















        3












        3








        3





        $begingroup$

        Normally it's limited by the cellphone battery voltage, which is about 3.7V. However there are other limits in play like the EU volume limit of 100dB - which is specified as SPL rather than a voltage.






        share|improve this answer









        $endgroup$



        Normally it's limited by the cellphone battery voltage, which is about 3.7V. However there are other limits in play like the EU volume limit of 100dB - which is specified as SPL rather than a voltage.







        share|improve this answer












        share|improve this answer



        share|improve this answer










        answered 22 hours ago









        pjc50pjc50

        34.4k34288




        34.4k34288






















            たくまいわき is a new contributor. Be nice, and check out our Code of Conduct.










            draft saved

            draft discarded


















            たくまいわき is a new contributor. Be nice, and check out our Code of Conduct.













            たくまいわき is a new contributor. Be nice, and check out our Code of Conduct.












            たくまいわき is a new contributor. Be nice, and check out our Code of Conduct.
















            Thanks for contributing an answer to Electrical Engineering Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function () {
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f429142%2fvoltage-of-sounds-of-mp3-files%23new-answer', 'question_page');
            }
            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            Færeyskur hestur Heimild | Tengill | Tilvísanir | LeiðsagnarvalRossið - síða um færeyska hrossið á færeyskuGott ár hjá færeyska hestinum

            He _____ here since 1970 . Answer needed [closed]What does “since he was so high” mean?Meaning of “catch birds for”?How do I ensure “since” takes the meaning I want?“Who cares here” meaningWhat does “right round toward” mean?the time tense (had now been detected)What does the phrase “ring around the roses” mean here?Correct usage of “visited upon”Meaning of “foiled rail sabotage bid”It was the third time I had gone to Rome or It is the third time I had been to Rome

            Slayer Innehåll Historia | Stil, komposition och lyrik | Bandets betydelse och framgångar | Sidoprojekt och samarbeten | Kontroverser | Medlemmar | Utmärkelser och nomineringar | Turnéer och festivaler | Diskografi | Referenser | Externa länkar | Navigeringsmenywww.slayer.net”Metal Massacre vol. 1””Metal Massacre vol. 3””Metal Massacre Volume III””Show No Mercy””Haunting the Chapel””Live Undead””Hell Awaits””Reign in Blood””Reign in Blood””Gold & Platinum – Reign in Blood””Golden Gods Awards Winners”originalet”Kerrang! Hall Of Fame””Slayer Looks Back On 37-Year Career In New Video Series: Part Two””South of Heaven””Gold & Platinum – South of Heaven””Seasons in the Abyss””Gold & Platinum - Seasons in the Abyss””Divine Intervention””Divine Intervention - Release group by Slayer””Gold & Platinum - Divine Intervention””Live Intrusion””Undisputed Attitude””Abolish Government/Superficial Love””Release “Slatanic Slaughter: A Tribute to Slayer” by Various Artists””Diabolus in Musica””Soundtrack to the Apocalypse””God Hates Us All””Systematic - Relationships””War at the Warfield””Gold & Platinum - War at the Warfield””Soundtrack to the Apocalypse””Gold & Platinum - Still Reigning””Metallica, Slayer, Iron Mauden Among Winners At Metal Hammer Awards””Eternal Pyre””Eternal Pyre - Slayer release group””Eternal Pyre””Metal Storm Awards 2006””Kerrang! Hall Of Fame””Slayer Wins 'Best Metal' Grammy Award””Slayer Guitarist Jeff Hanneman Dies””Bullet-For My Valentine booed at Metal Hammer Golden Gods Awards””Unholy Aliance””The End Of Slayer?””Slayer: We Could Thrash Out Two More Albums If We're Fast Enough...””'The Unholy Alliance: Chapter III' UK Dates Added”originalet”Megadeth And Slayer To Co-Headline 'Canadian Carnage' Trek”originalet”World Painted Blood””Release “World Painted Blood” by Slayer””Metallica Heading To Cinemas””Slayer, Megadeth To Join Forces For 'European Carnage' Tour - Dec. 18, 2010”originalet”Slayer's Hanneman Contracts Acute Infection; Band To Bring In Guest Guitarist””Cannibal Corpse's Pat O'Brien Will Step In As Slayer's Guest Guitarist”originalet”Slayer’s Jeff Hanneman Dead at 49””Dave Lombardo Says He Made Only $67,000 In 2011 While Touring With Slayer””Slayer: We Do Not Agree With Dave Lombardo's Substance Or Timeline Of Events””Slayer Welcomes Drummer Paul Bostaph Back To The Fold””Slayer Hope to Unveil Never-Before-Heard Jeff Hanneman Material on Next Album””Slayer Debut New Song 'Implode' During Surprise Golden Gods Appearance””Release group Repentless by Slayer””Repentless - Slayer - Credits””Slayer””Metal Storm Awards 2015””Slayer - to release comic book "Repentless #1"””Slayer To Release 'Repentless' 6.66" Vinyl Box Set””BREAKING NEWS: Slayer Announce Farewell Tour””Slayer Recruit Lamb of God, Anthrax, Behemoth + Testament for Final Tour””Slayer lägger ner efter 37 år””Slayer Announces Second North American Leg Of 'Final' Tour””Final World Tour””Slayer Announces Final European Tour With Lamb of God, Anthrax And Obituary””Slayer To Tour Europe With Lamb of God, Anthrax And Obituary””Slayer To Play 'Last French Show Ever' At Next Year's Hellfst””Slayer's Final World Tour Will Extend Into 2019””Death Angel's Rob Cavestany On Slayer's 'Farewell' Tour: 'Some Of Us Could See This Coming'””Testament Has No Plans To Retire Anytime Soon, Says Chuck Billy””Anthrax's Scott Ian On Slayer's 'Farewell' Tour Plans: 'I Was Surprised And I Wasn't Surprised'””Slayer””Slayer's Morbid Schlock””Review/Rock; For Slayer, the Mania Is the Message””Slayer - Biography””Slayer - Reign In Blood”originalet”Dave Lombardo””An exclusive oral history of Slayer”originalet”Exclusive! Interview With Slayer Guitarist Jeff Hanneman”originalet”Thinking Out Loud: Slayer's Kerry King on hair metal, Satan and being polite””Slayer Lyrics””Slayer - Biography””Most influential artists for extreme metal music””Slayer - Reign in Blood””Slayer guitarist Jeff Hanneman dies aged 49””Slatanic Slaughter: A Tribute to Slayer””Gateway to Hell: A Tribute to Slayer””Covered In Blood””Slayer: The Origins of Thrash in San Francisco, CA.””Why They Rule - #6 Slayer”originalet”Guitar World's 100 Greatest Heavy Metal Guitarists Of All Time”originalet”The fans have spoken: Slayer comes out on top in readers' polls”originalet”Tribute to Jeff Hanneman (1964-2013)””Lamb Of God Frontman: We Sound Like A Slayer Rip-Off””BEHEMOTH Frontman Pays Tribute To SLAYER's JEFF HANNEMAN””Slayer, Hatebreed Doing Double Duty On This Year's Ozzfest””System of a Down””Lacuna Coil’s Andrea Ferro Talks Influences, Skateboarding, Band Origins + More””Slayer - Reign in Blood””Into The Lungs of Hell””Slayer rules - en utställning om fans””Slayer and Their Fans Slashed Through a No-Holds-Barred Night at Gas Monkey””Home””Slayer””Gold & Platinum - The Big 4 Live from Sofia, Bulgaria””Exclusive! Interview With Slayer Guitarist Kerry King””2008-02-23: Wiltern, Los Angeles, CA, USA””Slayer's Kerry King To Perform With Megadeth Tonight! - Oct. 21, 2010”originalet”Dave Lombardo - Biography”Slayer Case DismissedArkiveradUltimate Classic Rock: Slayer guitarist Jeff Hanneman dead at 49.”Slayer: "We could never do any thing like Some Kind Of Monster..."””Cannibal Corpse'S Pat O'Brien Will Step In As Slayer'S Guest Guitarist | The Official Slayer Site”originalet”Slayer Wins 'Best Metal' Grammy Award””Slayer Guitarist Jeff Hanneman Dies””Kerrang! Awards 2006 Blog: Kerrang! Hall Of Fame””Kerrang! Awards 2013: Kerrang! Legend”originalet”Metallica, Slayer, Iron Maien Among Winners At Metal Hammer Awards””Metal Hammer Golden Gods Awards””Bullet For My Valentine Booed At Metal Hammer Golden Gods Awards””Metal Storm Awards 2006””Metal Storm Awards 2015””Slayer's Concert History””Slayer - Relationships””Slayer - Releases”Slayers officiella webbplatsSlayer på MusicBrainzOfficiell webbplatsSlayerSlayerr1373445760000 0001 1540 47353068615-5086262726cb13906545x(data)6033143kn20030215029