What are these (utility?) boxes at the side of the house?





.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty{
margin-bottom:0;
}








11















What are the four boxes in the picture below for? The fat pipe to the left goes up to the electricity meter. I've also included pictures of the two labels I could find.



Also, why is there a green plastic rope coming out of the first box? I found the box slightly gaping with the bottom screw missing1, and the rubber water seal around the cover a bit ripped where the rope is coming from. When I pull on the rope, there seems to be no resistance as if I could completely pull it out of the box. The fact that the seal is cut up where the rope is makes me think it wasn't supposed to be there in the first place...Should I pull out the rope and fix the seal of the box's cover?



1 I placed a new screw as seen in the picture, so that the box isn't gaping wide open (to rain, insects, etc.)...



4 boxes



box label



pipe










share|improve this question




















  • 1





    take off the covers and look inside

    – jsotola
    May 26 at 21:10






  • 7





    Power for... a pool? AC unit? Driveway or landscape lighting? Who knows what they're for. It's your house. What needs electricity outside? That should answer your question.

    – J...
    May 27 at 13:39













  • Probably outgoing wires. If ingoing wires were connected like this, I'd have a problem with it were it my house. Too easy to temper with.

    – Mast
    May 27 at 17:58






  • 1





    The fact that the green pull rope is straight and at an angle indicates that the end is buried in the gravel there. I'd suggest giving it a light tug to see if it comes up easily (if not, figure out why). Then consider rolling it up, taping the roll with some masking tape (to avoid leaving nasty residue) and gently putting it inside the cover of the box it comes out of. That way, when you replace the cover/gasket, it's not hanging out any more, but it's easy for the next electrician to grab.

    – FreeMan
    May 28 at 16:04


















11















What are the four boxes in the picture below for? The fat pipe to the left goes up to the electricity meter. I've also included pictures of the two labels I could find.



Also, why is there a green plastic rope coming out of the first box? I found the box slightly gaping with the bottom screw missing1, and the rubber water seal around the cover a bit ripped where the rope is coming from. When I pull on the rope, there seems to be no resistance as if I could completely pull it out of the box. The fact that the seal is cut up where the rope is makes me think it wasn't supposed to be there in the first place...Should I pull out the rope and fix the seal of the box's cover?



1 I placed a new screw as seen in the picture, so that the box isn't gaping wide open (to rain, insects, etc.)...



4 boxes



box label



pipe










share|improve this question




















  • 1





    take off the covers and look inside

    – jsotola
    May 26 at 21:10






  • 7





    Power for... a pool? AC unit? Driveway or landscape lighting? Who knows what they're for. It's your house. What needs electricity outside? That should answer your question.

    – J...
    May 27 at 13:39













  • Probably outgoing wires. If ingoing wires were connected like this, I'd have a problem with it were it my house. Too easy to temper with.

    – Mast
    May 27 at 17:58






  • 1





    The fact that the green pull rope is straight and at an angle indicates that the end is buried in the gravel there. I'd suggest giving it a light tug to see if it comes up easily (if not, figure out why). Then consider rolling it up, taping the roll with some masking tape (to avoid leaving nasty residue) and gently putting it inside the cover of the box it comes out of. That way, when you replace the cover/gasket, it's not hanging out any more, but it's easy for the next electrician to grab.

    – FreeMan
    May 28 at 16:04














11












11








11








What are the four boxes in the picture below for? The fat pipe to the left goes up to the electricity meter. I've also included pictures of the two labels I could find.



Also, why is there a green plastic rope coming out of the first box? I found the box slightly gaping with the bottom screw missing1, and the rubber water seal around the cover a bit ripped where the rope is coming from. When I pull on the rope, there seems to be no resistance as if I could completely pull it out of the box. The fact that the seal is cut up where the rope is makes me think it wasn't supposed to be there in the first place...Should I pull out the rope and fix the seal of the box's cover?



1 I placed a new screw as seen in the picture, so that the box isn't gaping wide open (to rain, insects, etc.)...



4 boxes



box label



pipe










share|improve this question














What are the four boxes in the picture below for? The fat pipe to the left goes up to the electricity meter. I've also included pictures of the two labels I could find.



Also, why is there a green plastic rope coming out of the first box? I found the box slightly gaping with the bottom screw missing1, and the rubber water seal around the cover a bit ripped where the rope is coming from. When I pull on the rope, there seems to be no resistance as if I could completely pull it out of the box. The fact that the seal is cut up where the rope is makes me think it wasn't supposed to be there in the first place...Should I pull out the rope and fix the seal of the box's cover?



1 I placed a new screw as seen in the picture, so that the box isn't gaping wide open (to rain, insects, etc.)...



4 boxes



box label



pipe







electrical utilities






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked May 26 at 19:09









Jet BlueJet Blue

1601 silver badge6 bronze badges




1601 silver badge6 bronze badges











  • 1





    take off the covers and look inside

    – jsotola
    May 26 at 21:10






  • 7





    Power for... a pool? AC unit? Driveway or landscape lighting? Who knows what they're for. It's your house. What needs electricity outside? That should answer your question.

    – J...
    May 27 at 13:39













  • Probably outgoing wires. If ingoing wires were connected like this, I'd have a problem with it were it my house. Too easy to temper with.

    – Mast
    May 27 at 17:58






  • 1





    The fact that the green pull rope is straight and at an angle indicates that the end is buried in the gravel there. I'd suggest giving it a light tug to see if it comes up easily (if not, figure out why). Then consider rolling it up, taping the roll with some masking tape (to avoid leaving nasty residue) and gently putting it inside the cover of the box it comes out of. That way, when you replace the cover/gasket, it's not hanging out any more, but it's easy for the next electrician to grab.

    – FreeMan
    May 28 at 16:04














  • 1





    take off the covers and look inside

    – jsotola
    May 26 at 21:10






  • 7





    Power for... a pool? AC unit? Driveway or landscape lighting? Who knows what they're for. It's your house. What needs electricity outside? That should answer your question.

    – J...
    May 27 at 13:39













  • Probably outgoing wires. If ingoing wires were connected like this, I'd have a problem with it were it my house. Too easy to temper with.

    – Mast
    May 27 at 17:58






  • 1





    The fact that the green pull rope is straight and at an angle indicates that the end is buried in the gravel there. I'd suggest giving it a light tug to see if it comes up easily (if not, figure out why). Then consider rolling it up, taping the roll with some masking tape (to avoid leaving nasty residue) and gently putting it inside the cover of the box it comes out of. That way, when you replace the cover/gasket, it's not hanging out any more, but it's easy for the next electrician to grab.

    – FreeMan
    May 28 at 16:04








1




1





take off the covers and look inside

– jsotola
May 26 at 21:10





take off the covers and look inside

– jsotola
May 26 at 21:10




7




7





Power for... a pool? AC unit? Driveway or landscape lighting? Who knows what they're for. It's your house. What needs electricity outside? That should answer your question.

– J...
May 27 at 13:39







Power for... a pool? AC unit? Driveway or landscape lighting? Who knows what they're for. It's your house. What needs electricity outside? That should answer your question.

– J...
May 27 at 13:39















Probably outgoing wires. If ingoing wires were connected like this, I'd have a problem with it were it my house. Too easy to temper with.

– Mast
May 27 at 17:58





Probably outgoing wires. If ingoing wires were connected like this, I'd have a problem with it were it my house. Too easy to temper with.

– Mast
May 27 at 17:58




1




1





The fact that the green pull rope is straight and at an angle indicates that the end is buried in the gravel there. I'd suggest giving it a light tug to see if it comes up easily (if not, figure out why). Then consider rolling it up, taping the roll with some masking tape (to avoid leaving nasty residue) and gently putting it inside the cover of the box it comes out of. That way, when you replace the cover/gasket, it's not hanging out any more, but it's easy for the next electrician to grab.

– FreeMan
May 28 at 16:04





The fact that the green pull rope is straight and at an angle indicates that the end is buried in the gravel there. I'd suggest giving it a light tug to see if it comes up easily (if not, figure out why). Then consider rolling it up, taping the roll with some masking tape (to avoid leaving nasty residue) and gently putting it inside the cover of the box it comes out of. That way, when you replace the cover/gasket, it's not hanging out any more, but it's easy for the next electrician to grab.

– FreeMan
May 28 at 16:04










3 Answers
3






active

oldest

votes


















18
















That is non metallic (PVC) electrical conduit.



There must be wires in them that come from or go to the inside of the house to an out building or ?? .



The green cord could be left there for fishing ( pulling ) new wire from one of the ends. Have you seen this green cord near any other electrical fixtures?



The covers come off to facilitate fishing the wires, It can be difficult to fish the wires thru many bends, so with this setup, you can pull a length of wire from one direction thru the open body and then pull the remainder as you help feed in to the body to complete the turn, then put the cover back on.






share|improve this answer























  • 3





    The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

    – user101687
    May 26 at 19:46











  • Is this where an AC unit would be plugged in?

    – Jet Blue
    May 26 at 23:15






  • 1





    @JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

    – ThreePhaseEel
    May 27 at 0:32





















14
















These are conduit bodies



What you are looking at is a set of PVC electrical conduits that extend underground (maybe to outbuildings or such?) with wiring inside, as well as at least one pull rope (the green rope you see dangling outside one of them) that can be used to add more wire to that conduit.



Attached to these conduits coming out of the ground are LB conduit bodies that provide a means of making the tight bend into the wall that's still accessible, so the electrician can make the pull through the underground conduit up to the open body, as the covers come off, then finish the pull from the body to the panel or box the conduit terminates at. This is done as the pulling forces become excessive if a wire pull becomes too long or bendy; the NEC sets a limit of 360° of cumulative bend between pull points for this reason, for that matter.






share|improve this answer


























  • Thanks for the specific name and the explanation, it all makes much more sense now.

    – Jet Blue
    May 27 at 3:44





















8
















First, get a nice strong magnet and pick through gravel below for that missing screw.



Regardless, take that cover off and bring it to a few local electrical supply houses (NOT big-box stores) and see if any of them sell that same PVC conduit body. They may be able to sell you a cover, but which brands they carry will vary. Obviously you want one that carries that brand of conduit body, so call ahead. It was a huge mistake to leave that rope dangling out of the gasket, as it wrecked the gasket.



The rope is in there for future pulling. Most people's tendency is to assume "the last person" was a fool. My rule is assume the last person did that thing for a reason, and you just haven't caught up with the reason yet. At some point in the future you will want something, and with any luck it'll be related and voila.



Expect that aged rope to be flimsy as heck. It will have been sitting in water for years. Don't pull wires with it - pull a new rope similar to it, then use that to pull the wires. The water isn't because of the missing screw. The water is because all underground wiring is 100% under water 100% of the time no matter how much we try to seal it, or that's the assumption we make. Trying to make conduit actually watertight is a lost cause, unless you go to industrial extremes like pressurizing it to 2 PSI. And there's no reason to bother; wet-rated wire such as THWN-2 or XHHW is rated for 100% water contact.



Also by the way, don't use cables in conduit. It's legal, just unnecessarily difficult. Use individual wires (that are wet-rated such as THWN-2 or XHHW). Besides, NM/Romex isn't wet rated).



Lastly, if that conduit is anything other than a northern exposure, paint it otherwise UV damage will tear it up. 1) Lightly sand it with a green Scotchbrite pad so the primer will stick, 2) brush an alkyd primer like Kilz Original or Rustoleum 7780 (use an 80 cent cheapie natural bristle brush, it won't clean with water, just throw it away), give it a month to cure, then 3) top with your house's latex paint.






share|improve this answer























  • 2





    Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

    – nigel222
    May 28 at 12:23













Your Answer








StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);

StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});

function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/4.0/"u003ecc by-sa 4.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});


}
});















draft saved

draft discarded
















StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f165923%2fwhat-are-these-utility-boxes-at-the-side-of-the-house%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown

























3 Answers
3






active

oldest

votes








3 Answers
3






active

oldest

votes









active

oldest

votes






active

oldest

votes









18
















That is non metallic (PVC) electrical conduit.



There must be wires in them that come from or go to the inside of the house to an out building or ?? .



The green cord could be left there for fishing ( pulling ) new wire from one of the ends. Have you seen this green cord near any other electrical fixtures?



The covers come off to facilitate fishing the wires, It can be difficult to fish the wires thru many bends, so with this setup, you can pull a length of wire from one direction thru the open body and then pull the remainder as you help feed in to the body to complete the turn, then put the cover back on.






share|improve this answer























  • 3





    The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

    – user101687
    May 26 at 19:46











  • Is this where an AC unit would be plugged in?

    – Jet Blue
    May 26 at 23:15






  • 1





    @JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

    – ThreePhaseEel
    May 27 at 0:32


















18
















That is non metallic (PVC) electrical conduit.



There must be wires in them that come from or go to the inside of the house to an out building or ?? .



The green cord could be left there for fishing ( pulling ) new wire from one of the ends. Have you seen this green cord near any other electrical fixtures?



The covers come off to facilitate fishing the wires, It can be difficult to fish the wires thru many bends, so with this setup, you can pull a length of wire from one direction thru the open body and then pull the remainder as you help feed in to the body to complete the turn, then put the cover back on.






share|improve this answer























  • 3





    The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

    – user101687
    May 26 at 19:46











  • Is this where an AC unit would be plugged in?

    – Jet Blue
    May 26 at 23:15






  • 1





    @JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

    – ThreePhaseEel
    May 27 at 0:32
















18














18










18









That is non metallic (PVC) electrical conduit.



There must be wires in them that come from or go to the inside of the house to an out building or ?? .



The green cord could be left there for fishing ( pulling ) new wire from one of the ends. Have you seen this green cord near any other electrical fixtures?



The covers come off to facilitate fishing the wires, It can be difficult to fish the wires thru many bends, so with this setup, you can pull a length of wire from one direction thru the open body and then pull the remainder as you help feed in to the body to complete the turn, then put the cover back on.






share|improve this answer















That is non metallic (PVC) electrical conduit.



There must be wires in them that come from or go to the inside of the house to an out building or ?? .



The green cord could be left there for fishing ( pulling ) new wire from one of the ends. Have you seen this green cord near any other electrical fixtures?



The covers come off to facilitate fishing the wires, It can be difficult to fish the wires thru many bends, so with this setup, you can pull a length of wire from one direction thru the open body and then pull the remainder as you help feed in to the body to complete the turn, then put the cover back on.







share|improve this answer














share|improve this answer



share|improve this answer








edited May 26 at 23:20









ThreePhaseEel

36.9k11 gold badges56 silver badges111 bronze badges




36.9k11 gold badges56 silver badges111 bronze badges










answered May 26 at 19:21









Alaska ManAlaska Man

5,0845 silver badges14 bronze badges




5,0845 silver badges14 bronze badges











  • 3





    The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

    – user101687
    May 26 at 19:46











  • Is this where an AC unit would be plugged in?

    – Jet Blue
    May 26 at 23:15






  • 1





    @JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

    – ThreePhaseEel
    May 27 at 0:32
















  • 3





    The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

    – user101687
    May 26 at 19:46











  • Is this where an AC unit would be plugged in?

    – Jet Blue
    May 26 at 23:15






  • 1





    @JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

    – ThreePhaseEel
    May 27 at 0:32










3




3





The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

– user101687
May 26 at 19:46





The green line is for a pull rope that was put in for future work.Try to put something on it so it does not fall into pipe Do not pull the rope back just leave it.. If you pulled some back just push it back in. a shop vac may be able to recover line You can get a new gasket replace it and add a new screw.. It is fine and wont hurt nothing the were planing ahead to benefit you done all the time.

– user101687
May 26 at 19:46













Is this where an AC unit would be plugged in?

– Jet Blue
May 26 at 23:15





Is this where an AC unit would be plugged in?

– Jet Blue
May 26 at 23:15




1




1





@JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

– ThreePhaseEel
May 27 at 0:32







@JetBlue -- one of the conduits might lead off to an A/C outdoor unit, perhaps (or more precisely, the associated disconnect box). It wouldn't be "plugged in" per se, though, but hardwired

– ThreePhaseEel
May 27 at 0:32















14
















These are conduit bodies



What you are looking at is a set of PVC electrical conduits that extend underground (maybe to outbuildings or such?) with wiring inside, as well as at least one pull rope (the green rope you see dangling outside one of them) that can be used to add more wire to that conduit.



Attached to these conduits coming out of the ground are LB conduit bodies that provide a means of making the tight bend into the wall that's still accessible, so the electrician can make the pull through the underground conduit up to the open body, as the covers come off, then finish the pull from the body to the panel or box the conduit terminates at. This is done as the pulling forces become excessive if a wire pull becomes too long or bendy; the NEC sets a limit of 360° of cumulative bend between pull points for this reason, for that matter.






share|improve this answer


























  • Thanks for the specific name and the explanation, it all makes much more sense now.

    – Jet Blue
    May 27 at 3:44


















14
















These are conduit bodies



What you are looking at is a set of PVC electrical conduits that extend underground (maybe to outbuildings or such?) with wiring inside, as well as at least one pull rope (the green rope you see dangling outside one of them) that can be used to add more wire to that conduit.



Attached to these conduits coming out of the ground are LB conduit bodies that provide a means of making the tight bend into the wall that's still accessible, so the electrician can make the pull through the underground conduit up to the open body, as the covers come off, then finish the pull from the body to the panel or box the conduit terminates at. This is done as the pulling forces become excessive if a wire pull becomes too long or bendy; the NEC sets a limit of 360° of cumulative bend between pull points for this reason, for that matter.






share|improve this answer


























  • Thanks for the specific name and the explanation, it all makes much more sense now.

    – Jet Blue
    May 27 at 3:44
















14














14










14









These are conduit bodies



What you are looking at is a set of PVC electrical conduits that extend underground (maybe to outbuildings or such?) with wiring inside, as well as at least one pull rope (the green rope you see dangling outside one of them) that can be used to add more wire to that conduit.



Attached to these conduits coming out of the ground are LB conduit bodies that provide a means of making the tight bend into the wall that's still accessible, so the electrician can make the pull through the underground conduit up to the open body, as the covers come off, then finish the pull from the body to the panel or box the conduit terminates at. This is done as the pulling forces become excessive if a wire pull becomes too long or bendy; the NEC sets a limit of 360° of cumulative bend between pull points for this reason, for that matter.






share|improve this answer













These are conduit bodies



What you are looking at is a set of PVC electrical conduits that extend underground (maybe to outbuildings or such?) with wiring inside, as well as at least one pull rope (the green rope you see dangling outside one of them) that can be used to add more wire to that conduit.



Attached to these conduits coming out of the ground are LB conduit bodies that provide a means of making the tight bend into the wall that's still accessible, so the electrician can make the pull through the underground conduit up to the open body, as the covers come off, then finish the pull from the body to the panel or box the conduit terminates at. This is done as the pulling forces become excessive if a wire pull becomes too long or bendy; the NEC sets a limit of 360° of cumulative bend between pull points for this reason, for that matter.







share|improve this answer












share|improve this answer



share|improve this answer










answered May 26 at 23:26









ThreePhaseEelThreePhaseEel

36.9k11 gold badges56 silver badges111 bronze badges




36.9k11 gold badges56 silver badges111 bronze badges
















  • Thanks for the specific name and the explanation, it all makes much more sense now.

    – Jet Blue
    May 27 at 3:44





















  • Thanks for the specific name and the explanation, it all makes much more sense now.

    – Jet Blue
    May 27 at 3:44



















Thanks for the specific name and the explanation, it all makes much more sense now.

– Jet Blue
May 27 at 3:44







Thanks for the specific name and the explanation, it all makes much more sense now.

– Jet Blue
May 27 at 3:44













8
















First, get a nice strong magnet and pick through gravel below for that missing screw.



Regardless, take that cover off and bring it to a few local electrical supply houses (NOT big-box stores) and see if any of them sell that same PVC conduit body. They may be able to sell you a cover, but which brands they carry will vary. Obviously you want one that carries that brand of conduit body, so call ahead. It was a huge mistake to leave that rope dangling out of the gasket, as it wrecked the gasket.



The rope is in there for future pulling. Most people's tendency is to assume "the last person" was a fool. My rule is assume the last person did that thing for a reason, and you just haven't caught up with the reason yet. At some point in the future you will want something, and with any luck it'll be related and voila.



Expect that aged rope to be flimsy as heck. It will have been sitting in water for years. Don't pull wires with it - pull a new rope similar to it, then use that to pull the wires. The water isn't because of the missing screw. The water is because all underground wiring is 100% under water 100% of the time no matter how much we try to seal it, or that's the assumption we make. Trying to make conduit actually watertight is a lost cause, unless you go to industrial extremes like pressurizing it to 2 PSI. And there's no reason to bother; wet-rated wire such as THWN-2 or XHHW is rated for 100% water contact.



Also by the way, don't use cables in conduit. It's legal, just unnecessarily difficult. Use individual wires (that are wet-rated such as THWN-2 or XHHW). Besides, NM/Romex isn't wet rated).



Lastly, if that conduit is anything other than a northern exposure, paint it otherwise UV damage will tear it up. 1) Lightly sand it with a green Scotchbrite pad so the primer will stick, 2) brush an alkyd primer like Kilz Original or Rustoleum 7780 (use an 80 cent cheapie natural bristle brush, it won't clean with water, just throw it away), give it a month to cure, then 3) top with your house's latex paint.






share|improve this answer























  • 2





    Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

    – nigel222
    May 28 at 12:23
















8
















First, get a nice strong magnet and pick through gravel below for that missing screw.



Regardless, take that cover off and bring it to a few local electrical supply houses (NOT big-box stores) and see if any of them sell that same PVC conduit body. They may be able to sell you a cover, but which brands they carry will vary. Obviously you want one that carries that brand of conduit body, so call ahead. It was a huge mistake to leave that rope dangling out of the gasket, as it wrecked the gasket.



The rope is in there for future pulling. Most people's tendency is to assume "the last person" was a fool. My rule is assume the last person did that thing for a reason, and you just haven't caught up with the reason yet. At some point in the future you will want something, and with any luck it'll be related and voila.



Expect that aged rope to be flimsy as heck. It will have been sitting in water for years. Don't pull wires with it - pull a new rope similar to it, then use that to pull the wires. The water isn't because of the missing screw. The water is because all underground wiring is 100% under water 100% of the time no matter how much we try to seal it, or that's the assumption we make. Trying to make conduit actually watertight is a lost cause, unless you go to industrial extremes like pressurizing it to 2 PSI. And there's no reason to bother; wet-rated wire such as THWN-2 or XHHW is rated for 100% water contact.



Also by the way, don't use cables in conduit. It's legal, just unnecessarily difficult. Use individual wires (that are wet-rated such as THWN-2 or XHHW). Besides, NM/Romex isn't wet rated).



Lastly, if that conduit is anything other than a northern exposure, paint it otherwise UV damage will tear it up. 1) Lightly sand it with a green Scotchbrite pad so the primer will stick, 2) brush an alkyd primer like Kilz Original or Rustoleum 7780 (use an 80 cent cheapie natural bristle brush, it won't clean with water, just throw it away), give it a month to cure, then 3) top with your house's latex paint.






share|improve this answer























  • 2





    Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

    – nigel222
    May 28 at 12:23














8














8










8









First, get a nice strong magnet and pick through gravel below for that missing screw.



Regardless, take that cover off and bring it to a few local electrical supply houses (NOT big-box stores) and see if any of them sell that same PVC conduit body. They may be able to sell you a cover, but which brands they carry will vary. Obviously you want one that carries that brand of conduit body, so call ahead. It was a huge mistake to leave that rope dangling out of the gasket, as it wrecked the gasket.



The rope is in there for future pulling. Most people's tendency is to assume "the last person" was a fool. My rule is assume the last person did that thing for a reason, and you just haven't caught up with the reason yet. At some point in the future you will want something, and with any luck it'll be related and voila.



Expect that aged rope to be flimsy as heck. It will have been sitting in water for years. Don't pull wires with it - pull a new rope similar to it, then use that to pull the wires. The water isn't because of the missing screw. The water is because all underground wiring is 100% under water 100% of the time no matter how much we try to seal it, or that's the assumption we make. Trying to make conduit actually watertight is a lost cause, unless you go to industrial extremes like pressurizing it to 2 PSI. And there's no reason to bother; wet-rated wire such as THWN-2 or XHHW is rated for 100% water contact.



Also by the way, don't use cables in conduit. It's legal, just unnecessarily difficult. Use individual wires (that are wet-rated such as THWN-2 or XHHW). Besides, NM/Romex isn't wet rated).



Lastly, if that conduit is anything other than a northern exposure, paint it otherwise UV damage will tear it up. 1) Lightly sand it with a green Scotchbrite pad so the primer will stick, 2) brush an alkyd primer like Kilz Original or Rustoleum 7780 (use an 80 cent cheapie natural bristle brush, it won't clean with water, just throw it away), give it a month to cure, then 3) top with your house's latex paint.






share|improve this answer















First, get a nice strong magnet and pick through gravel below for that missing screw.



Regardless, take that cover off and bring it to a few local electrical supply houses (NOT big-box stores) and see if any of them sell that same PVC conduit body. They may be able to sell you a cover, but which brands they carry will vary. Obviously you want one that carries that brand of conduit body, so call ahead. It was a huge mistake to leave that rope dangling out of the gasket, as it wrecked the gasket.



The rope is in there for future pulling. Most people's tendency is to assume "the last person" was a fool. My rule is assume the last person did that thing for a reason, and you just haven't caught up with the reason yet. At some point in the future you will want something, and with any luck it'll be related and voila.



Expect that aged rope to be flimsy as heck. It will have been sitting in water for years. Don't pull wires with it - pull a new rope similar to it, then use that to pull the wires. The water isn't because of the missing screw. The water is because all underground wiring is 100% under water 100% of the time no matter how much we try to seal it, or that's the assumption we make. Trying to make conduit actually watertight is a lost cause, unless you go to industrial extremes like pressurizing it to 2 PSI. And there's no reason to bother; wet-rated wire such as THWN-2 or XHHW is rated for 100% water contact.



Also by the way, don't use cables in conduit. It's legal, just unnecessarily difficult. Use individual wires (that are wet-rated such as THWN-2 or XHHW). Besides, NM/Romex isn't wet rated).



Lastly, if that conduit is anything other than a northern exposure, paint it otherwise UV damage will tear it up. 1) Lightly sand it with a green Scotchbrite pad so the primer will stick, 2) brush an alkyd primer like Kilz Original or Rustoleum 7780 (use an 80 cent cheapie natural bristle brush, it won't clean with water, just throw it away), give it a month to cure, then 3) top with your house's latex paint.







share|improve this answer














share|improve this answer



share|improve this answer








edited May 27 at 16:15

























answered May 27 at 16:02









HarperHarper

99.3k7 gold badges74 silver badges208 bronze badges




99.3k7 gold badges74 silver badges208 bronze badges











  • 2





    Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

    – nigel222
    May 28 at 12:23














  • 2





    Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

    – nigel222
    May 28 at 12:23








2




2





Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

– nigel222
May 28 at 12:23





Unless it's incredibly ancient I'd expect that green rope to be a rot-proof synthetic polymer, unless the person who put it in was intending to use it within a month.

– nigel222
May 28 at 12:23



















draft saved

draft discarded



















































Thanks for contributing an answer to Home Improvement Stack Exchange!


  • Please be sure to answer the question. Provide details and share your research!

But avoid



  • Asking for help, clarification, or responding to other answers.

  • Making statements based on opinion; back them up with references or personal experience.


To learn more, see our tips on writing great answers.




draft saved


draft discarded














StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f165923%2fwhat-are-these-utility-boxes-at-the-side-of-the-house%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown





















































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown

































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown







Popular posts from this blog

Færeyskur hestur Heimild | Tengill | Tilvísanir | LeiðsagnarvalRossið - síða um færeyska hrossið á færeyskuGott ár hjá færeyska hestinum

He _____ here since 1970 . Answer needed [closed]What does “since he was so high” mean?Meaning of “catch birds for”?How do I ensure “since” takes the meaning I want?“Who cares here” meaningWhat does “right round toward” mean?the time tense (had now been detected)What does the phrase “ring around the roses” mean here?Correct usage of “visited upon”Meaning of “foiled rail sabotage bid”It was the third time I had gone to Rome or It is the third time I had been to Rome

Slayer Innehåll Historia | Stil, komposition och lyrik | Bandets betydelse och framgångar | Sidoprojekt och samarbeten | Kontroverser | Medlemmar | Utmärkelser och nomineringar | Turnéer och festivaler | Diskografi | Referenser | Externa länkar | Navigeringsmenywww.slayer.net”Metal Massacre vol. 1””Metal Massacre vol. 3””Metal Massacre Volume III””Show No Mercy””Haunting the Chapel””Live Undead””Hell Awaits””Reign in Blood””Reign in Blood””Gold & Platinum – Reign in Blood””Golden Gods Awards Winners”originalet”Kerrang! Hall Of Fame””Slayer Looks Back On 37-Year Career In New Video Series: Part Two””South of Heaven””Gold & Platinum – South of Heaven””Seasons in the Abyss””Gold & Platinum - Seasons in the Abyss””Divine Intervention””Divine Intervention - Release group by Slayer””Gold & Platinum - Divine Intervention””Live Intrusion””Undisputed Attitude””Abolish Government/Superficial Love””Release “Slatanic Slaughter: A Tribute to Slayer” by Various Artists””Diabolus in Musica””Soundtrack to the Apocalypse””God Hates Us All””Systematic - Relationships””War at the Warfield””Gold & Platinum - War at the Warfield””Soundtrack to the Apocalypse””Gold & Platinum - Still Reigning””Metallica, Slayer, Iron Mauden Among Winners At Metal Hammer Awards””Eternal Pyre””Eternal Pyre - Slayer release group””Eternal Pyre””Metal Storm Awards 2006””Kerrang! Hall Of Fame””Slayer Wins 'Best Metal' Grammy Award””Slayer Guitarist Jeff Hanneman Dies””Bullet-For My Valentine booed at Metal Hammer Golden Gods Awards””Unholy Aliance””The End Of Slayer?””Slayer: We Could Thrash Out Two More Albums If We're Fast Enough...””'The Unholy Alliance: Chapter III' UK Dates Added”originalet”Megadeth And Slayer To Co-Headline 'Canadian Carnage' Trek”originalet”World Painted Blood””Release “World Painted Blood” by Slayer””Metallica Heading To Cinemas””Slayer, Megadeth To Join Forces For 'European Carnage' Tour - Dec. 18, 2010”originalet”Slayer's Hanneman Contracts Acute Infection; Band To Bring In Guest Guitarist””Cannibal Corpse's Pat O'Brien Will Step In As Slayer's Guest Guitarist”originalet”Slayer’s Jeff Hanneman Dead at 49””Dave Lombardo Says He Made Only $67,000 In 2011 While Touring With Slayer””Slayer: We Do Not Agree With Dave Lombardo's Substance Or Timeline Of Events””Slayer Welcomes Drummer Paul Bostaph Back To The Fold””Slayer Hope to Unveil Never-Before-Heard Jeff Hanneman Material on Next Album””Slayer Debut New Song 'Implode' During Surprise Golden Gods Appearance””Release group Repentless by Slayer””Repentless - Slayer - Credits””Slayer””Metal Storm Awards 2015””Slayer - to release comic book "Repentless #1"””Slayer To Release 'Repentless' 6.66" Vinyl Box Set””BREAKING NEWS: Slayer Announce Farewell Tour””Slayer Recruit Lamb of God, Anthrax, Behemoth + Testament for Final Tour””Slayer lägger ner efter 37 år””Slayer Announces Second North American Leg Of 'Final' Tour””Final World Tour””Slayer Announces Final European Tour With Lamb of God, Anthrax And Obituary””Slayer To Tour Europe With Lamb of God, Anthrax And Obituary””Slayer To Play 'Last French Show Ever' At Next Year's Hellfst””Slayer's Final World Tour Will Extend Into 2019””Death Angel's Rob Cavestany On Slayer's 'Farewell' Tour: 'Some Of Us Could See This Coming'””Testament Has No Plans To Retire Anytime Soon, Says Chuck Billy””Anthrax's Scott Ian On Slayer's 'Farewell' Tour Plans: 'I Was Surprised And I Wasn't Surprised'””Slayer””Slayer's Morbid Schlock””Review/Rock; For Slayer, the Mania Is the Message””Slayer - Biography””Slayer - Reign In Blood”originalet”Dave Lombardo””An exclusive oral history of Slayer”originalet”Exclusive! Interview With Slayer Guitarist Jeff Hanneman”originalet”Thinking Out Loud: Slayer's Kerry King on hair metal, Satan and being polite””Slayer Lyrics””Slayer - Biography””Most influential artists for extreme metal music””Slayer - Reign in Blood””Slayer guitarist Jeff Hanneman dies aged 49””Slatanic Slaughter: A Tribute to Slayer””Gateway to Hell: A Tribute to Slayer””Covered In Blood””Slayer: The Origins of Thrash in San Francisco, CA.””Why They Rule - #6 Slayer”originalet”Guitar World's 100 Greatest Heavy Metal Guitarists Of All Time”originalet”The fans have spoken: Slayer comes out on top in readers' polls”originalet”Tribute to Jeff Hanneman (1964-2013)””Lamb Of God Frontman: We Sound Like A Slayer Rip-Off””BEHEMOTH Frontman Pays Tribute To SLAYER's JEFF HANNEMAN””Slayer, Hatebreed Doing Double Duty On This Year's Ozzfest””System of a Down””Lacuna Coil’s Andrea Ferro Talks Influences, Skateboarding, Band Origins + More””Slayer - Reign in Blood””Into The Lungs of Hell””Slayer rules - en utställning om fans””Slayer and Their Fans Slashed Through a No-Holds-Barred Night at Gas Monkey””Home””Slayer””Gold & Platinum - The Big 4 Live from Sofia, Bulgaria””Exclusive! Interview With Slayer Guitarist Kerry King””2008-02-23: Wiltern, Los Angeles, CA, USA””Slayer's Kerry King To Perform With Megadeth Tonight! - Oct. 21, 2010”originalet”Dave Lombardo - Biography”Slayer Case DismissedArkiveradUltimate Classic Rock: Slayer guitarist Jeff Hanneman dead at 49.”Slayer: "We could never do any thing like Some Kind Of Monster..."””Cannibal Corpse'S Pat O'Brien Will Step In As Slayer'S Guest Guitarist | The Official Slayer Site”originalet”Slayer Wins 'Best Metal' Grammy Award””Slayer Guitarist Jeff Hanneman Dies””Kerrang! Awards 2006 Blog: Kerrang! Hall Of Fame””Kerrang! Awards 2013: Kerrang! Legend”originalet”Metallica, Slayer, Iron Maien Among Winners At Metal Hammer Awards””Metal Hammer Golden Gods Awards””Bullet For My Valentine Booed At Metal Hammer Golden Gods Awards””Metal Storm Awards 2006””Metal Storm Awards 2015””Slayer's Concert History””Slayer - Relationships””Slayer - Releases”Slayers officiella webbplatsSlayer på MusicBrainzOfficiell webbplatsSlayerSlayerr1373445760000 0001 1540 47353068615-5086262726cb13906545x(data)6033143kn20030215029