Why did CATV standarize in 75 ohms and everyone else in 50?How is transmission line impedance selected?Industry standard Cat5e cablingWhy Characteristic Impedance must be 50 ohms?Why Inductor reactance 180 ohms?Why do cables have multiple grounds?Where did Bootstrapping get its name?What does S stand for in 75 S ohms?How did wireless telegraphy reach so far?What frequency did wireless telegraphs operate at?Problem understanding CDMA and W-CDMAStandard 2.54/1.27mm pinheader impedance
Is “snitty” a popular American English term? What is its origin?
Is Benjen dead?
Desolate vs deserted
Importing a Part of the JSON
Using Im[] and Re[] Correctly
Is 'contemporary' ambiguous and if so is there a better word?
Are there terms in German for different skull shapes?
How to deal with employer who keeps me at work after working hours
Will 700 more planes a day fly because of the Heathrow expansion?
Which Sphere is Fastest?
Any examples of liquids volatile at room temp but non-flammable?
How to pass hash as password to ssh server
Why would a military not separate its forces into different branches?
What to use instead of cling film to wrap pastry
How does the reduce() method work in Java 8?
What do I do if my advisor made a mistake?
How to ask systemd to not start a system service on boot?
How can internet speed be 10 times slower without a router than when using a router?
Why am I receiving the identity insert error even after explicitly setting IDENTITY_INSERT ON and using a column list?
Is the book wrong about the Nyquist Sampling Criterion?
Out of scope work duties and resignation
Why is my arithmetic with a long long int behaving this way?
Voltage Balun 1:1
Should I simplify my writing in a foreign country?
Why did CATV standarize in 75 ohms and everyone else in 50?
How is transmission line impedance selected?Industry standard Cat5e cablingWhy Characteristic Impedance must be 50 ohms?Why Inductor reactance 180 ohms?Why do cables have multiple grounds?Where did Bootstrapping get its name?What does S stand for in 75 S ohms?How did wireless telegraphy reach so far?What frequency did wireless telegraphs operate at?Problem understanding CDMA and W-CDMAStandard 2.54/1.27mm pinheader impedance
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty margin-bottom:0;
$begingroup$
All of the CATV industry runs on 75 ohm systems, while most of the rest of the radio world uses 50 ohms.
Why was this standard chosen?
I was wondering this because good quality RG6 cable can be obtained everywhere for very little, compared to decent quality 50 ohm cabling.
impedance cables telecommunications coaxial
asked Mar 30 at 17:43
hjfhjf
5022823
$endgroup$
|
show 1 more comment
$begingroup$
All of the CATV industry runs on 75 ohm systems, while most of the rest of the radio world uses 50 ohms.
Why was this standard chosen?
I was wondering this because good quality RG6 cable can be obtained everywhere for very little, compared to decent quality 50 ohm cabling.
impedance cables telecommunications coaxial
asked Mar 30 at 17:43
hjfhjf
5022823
$endgroup$
$begingroup$
Some insight is in Andy's answer:electronics.stackexchange.com/questions/350451/…
$endgroup$
– glen_geek
Mar 30 at 17:49
1
$begingroup$
I'm not sure if I should say "a substantial minority" or "enough so that it's known" -- but there are radio amateurs who use 75 ohm transmission line for this reason. If you're going to run an antenna tuner anyway, and if you're going to build your own antennas anyway, then it's not a bad way to get a bit more bang for the buck.
$endgroup$
– TimWescott
Mar 30 at 18:11
$begingroup$
@TimWescott specifically, this: qsl.net/g4hbt/dipole.htm antenna specifies a 75 ohm line. I finally understand why.
$endgroup$
– hjf
Mar 30 at 18:13
1
$begingroup$
It was 75 ohms for RF signals before cable TV was a "thing". I've always figured it was the cable manufacturers, so they could force you to buy two spools of cable instead of just one. And the connector manufacturers, so they could sell you two different sizes of connectors.
$endgroup$
– Hot Licks
Mar 30 at 19:07
2
$begingroup$
Possible duplicate of How is transmission line impedance selected?
$endgroup$
– Dmitry Grigoryev
Apr 1 at 11:17
|
show 1 more comment
$begingroup$
All of the CATV industry runs on 75 ohm systems, while most of the rest of the radio world uses 50 ohms.
Why was this standard chosen?
I was wondering this because good quality RG6 cable can be obtained everywhere for very little, compared to decent quality 50 ohm cabling.
impedance cables telecommunications coaxial
asked Mar 30 at 17:43
hjfhjf
5022823
$endgroup$
All of the CATV industry runs on 75 ohm systems, while most of the rest of the radio world uses 50 ohms.
Why was this standard chosen?
I was wondering this because good quality RG6 cable can be obtained everywhere for very little, compared to decent quality 50 ohm cabling.
impedance cables telecommunications coaxial
impedance cables telecommunications coaxial
asked Mar 30 at 17:43
hjfhjf
5022823
asked Mar 30 at 17:43
hjfhjf
5022823
asked Mar 30 at 17:43
hjfhjf
5022823
asked Mar 30 at 17:43
hjfhjf
5022823
asked Mar 30 at 17:43
hjfhjf
5022823
5022823
$begingroup$
Some insight is in Andy's answer:electronics.stackexchange.com/questions/350451/…
$endgroup$
– glen_geek
Mar 30 at 17:49
1
$begingroup$
I'm not sure if I should say "a substantial minority" or "enough so that it's known" -- but there are radio amateurs who use 75 ohm transmission line for this reason. If you're going to run an antenna tuner anyway, and if you're going to build your own antennas anyway, then it's not a bad way to get a bit more bang for the buck.
$endgroup$
– TimWescott
Mar 30 at 18:11
$begingroup$
@TimWescott specifically, this: qsl.net/g4hbt/dipole.htm antenna specifies a 75 ohm line. I finally understand why.
$endgroup$
– hjf
Mar 30 at 18:13
1
$begingroup$
It was 75 ohms for RF signals before cable TV was a "thing". I've always figured it was the cable manufacturers, so they could force you to buy two spools of cable instead of just one. And the connector manufacturers, so they could sell you two different sizes of connectors.
$endgroup$
– Hot Licks
Mar 30 at 19:07
2
$begingroup$
Possible duplicate of How is transmission line impedance selected?
$endgroup$
– Dmitry Grigoryev
Apr 1 at 11:17
|
show 1 more comment
$begingroup$
Some insight is in Andy's answer:electronics.stackexchange.com/questions/350451/…
$endgroup$
– glen_geek
Mar 30 at 17:49
1
$begingroup$
I'm not sure if I should say "a substantial minority" or "enough so that it's known" -- but there are radio amateurs who use 75 ohm transmission line for this reason. If you're going to run an antenna tuner anyway, and if you're going to build your own antennas anyway, then it's not a bad way to get a bit more bang for the buck.
$endgroup$
– TimWescott
Mar 30 at 18:11
$begingroup$
@TimWescott specifically, this: qsl.net/g4hbt/dipole.htm antenna specifies a 75 ohm line. I finally understand why.
$endgroup$
– hjf
Mar 30 at 18:13
1
$begingroup$
It was 75 ohms for RF signals before cable TV was a "thing". I've always figured it was the cable manufacturers, so they could force you to buy two spools of cable instead of just one. And the connector manufacturers, so they could sell you two different sizes of connectors.
$endgroup$
– Hot Licks
Mar 30 at 19:07
2
$begingroup$
Possible duplicate of How is transmission line impedance selected?
$endgroup$
– Dmitry Grigoryev
Apr 1 at 11:17
$begingroup$
Some insight is in Andy's answer:electronics.stackexchange.com/questions/350451/…
$endgroup$
– glen_geek
Mar 30 at 17:49
$begingroup$
Some insight is in Andy's answer:electronics.stackexchange.com/questions/350451/…
$endgroup$
– glen_geek
Mar 30 at 17:49
1
1
$begingroup$
I'm not sure if I should say "a substantial minority" or "enough so that it's known" -- but there are radio amateurs who use 75 ohm transmission line for this reason. If you're going to run an antenna tuner anyway, and if you're going to build your own antennas anyway, then it's not a bad way to get a bit more bang for the buck.
$endgroup$
– TimWescott
Mar 30 at 18:11
$begingroup$
I'm not sure if I should say "a substantial minority" or "enough so that it's known" -- but there are radio amateurs who use 75 ohm transmission line for this reason. If you're going to run an antenna tuner anyway, and if you're going to build your own antennas anyway, then it's not a bad way to get a bit more bang for the buck.
$endgroup$
– TimWescott
Mar 30 at 18:11
$begingroup$
@TimWescott specifically, this: qsl.net/g4hbt/dipole.htm antenna specifies a 75 ohm line. I finally understand why.
$endgroup$
– hjf
Mar 30 at 18:13
$begingroup$
@TimWescott specifically, this: qsl.net/g4hbt/dipole.htm antenna specifies a 75 ohm line. I finally understand why.
$endgroup$
– hjf
Mar 30 at 18:13
1
1
$begingroup$
It was 75 ohms for RF signals before cable TV was a "thing". I've always figured it was the cable manufacturers, so they could force you to buy two spools of cable instead of just one. And the connector manufacturers, so they could sell you two different sizes of connectors.
$endgroup$
– Hot Licks
Mar 30 at 19:07
$begingroup$
It was 75 ohms for RF signals before cable TV was a "thing". I've always figured it was the cable manufacturers, so they could force you to buy two spools of cable instead of just one. And the connector manufacturers, so they could sell you two different sizes of connectors.
$endgroup$
– Hot Licks
Mar 30 at 19:07
2
2
$begingroup$
Possible duplicate of How is transmission line impedance selected?
$endgroup$
– Dmitry Grigoryev
Apr 1 at 11:17
$begingroup$
Possible duplicate of How is transmission line impedance selected?
$endgroup$
– Dmitry Grigoryev
Apr 1 at 11:17
|
show 1 more comment
1 Answer
1
active
oldest
votes
$begingroup$
How is transmission line impedance selected? explains why transmission line impedance matters.
The CATV industry deals with low-level signals, so it cares ONLY about loss and not at all about power-handling. That's why they chose 75Ω transmission lines.
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
$endgroup$
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f429843%2fwhy-did-catv-standarize-in-75-ohms-and-everyone-else-in-50%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
How is transmission line impedance selected? explains why transmission line impedance matters.
The CATV industry deals with low-level signals, so it cares ONLY about loss and not at all about power-handling. That's why they chose 75Ω transmission lines.
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
$endgroup$
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
add a comment |
$begingroup$
How is transmission line impedance selected? explains why transmission line impedance matters.
The CATV industry deals with low-level signals, so it cares ONLY about loss and not at all about power-handling. That's why they chose 75Ω transmission lines.
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
$endgroup$
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
add a comment |
$begingroup$
How is transmission line impedance selected? explains why transmission line impedance matters.
The CATV industry deals with low-level signals, so it cares ONLY about loss and not at all about power-handling. That's why they chose 75Ω transmission lines.
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
$endgroup$
How is transmission line impedance selected? explains why transmission line impedance matters.
The CATV industry deals with low-level signals, so it cares ONLY about loss and not at all about power-handling. That's why they chose 75Ω transmission lines.
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
answered Mar 30 at 17:55
Dave Tweed♦Dave Tweed
126k10155271
126k10155271
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
add a comment |
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
$begingroup$
Awesome! I didn't know that thing about power, and now I also understand why NOAA reception turnstile antennas specify 75 ohms too!
$endgroup$
– hjf
Mar 30 at 18:01
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f429843%2fwhy-did-catv-standarize-in-75-ohms-and-everyone-else-in-50%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
Some insight is in Andy's answer:electronics.stackexchange.com/questions/350451/…
$endgroup$
– glen_geek
Mar 30 at 17:49
1
$begingroup$
I'm not sure if I should say "a substantial minority" or "enough so that it's known" -- but there are radio amateurs who use 75 ohm transmission line for this reason. If you're going to run an antenna tuner anyway, and if you're going to build your own antennas anyway, then it's not a bad way to get a bit more bang for the buck.
$endgroup$
– TimWescott
Mar 30 at 18:11
$begingroup$
@TimWescott specifically, this: qsl.net/g4hbt/dipole.htm antenna specifies a 75 ohm line. I finally understand why.
$endgroup$
– hjf
Mar 30 at 18:13
1
$begingroup$
It was 75 ohms for RF signals before cable TV was a "thing". I've always figured it was the cable manufacturers, so they could force you to buy two spools of cable instead of just one. And the connector manufacturers, so they could sell you two different sizes of connectors.
$endgroup$
– Hot Licks
Mar 30 at 19:07
2
$begingroup$
Possible duplicate of How is transmission line impedance selected?
$endgroup$
– Dmitry Grigoryev
Apr 1 at 11:17